防锈铝板要具备的制作要点_新闻资讯

四川11选5

德成铝业

您的位置:四川11选5 > 新闻资讯 >

防锈铝板要具备的制作要点

来源:http://www.jnggsdz.com

1、贮存:应将防锈铝板存放于干燥通风处,且平放在平整的表面上,切勿踩踏、撞击。
1, storage: the antirust aluminum plate should be stored in the dry and ventilated place, and flat on the surface of the flat, do not trample or impact.
2、搬运:搬运板材应将板的四边同时抬起,严禁推拉、抽取,以免刮伤板面。
2, handling: moving plate should lift the four sides of the plate at the same time, strictly prohibit pushing and pulling, so as to avoid scraping the surface of the plate.
3、开槽:用开槽机或锣机开槽时,应使用半圆头式大于90度的铣刀.下刀既不要过深伤及防锈铝板,也不要过浅使折边困难,应留有0.2-0.3MM厚塑料芯材连同铝板一起弯边,以增加强度和韧性,否则在弯边时铝板可能断裂或漆膜爆裂。
3, use: slotted slotting machine or gong machine slot, should use more than 90 of the cutter head semicircle. The knife is not too deep and antirust aluminum, not too shallow to hem difficulties, should be 0.2-0.3MM thick plastic core material with aluminum plate bending together, in order to increase the strength and toughness, not in bending the plate or film may burst fracture.
4、弯边:弯边时需用力均匀,一次成型,不要反复弯折,否则防锈铝板可能断裂。
4, bending edge: when the edge must be forced evenly, one molding, do not bend repeatedly, otherwise the antirust aluminum plate may break.

铝卷生产厂家
5、弧形加工:加工弧形应使用专用弯曲设备加工,徐徐用力,使板材逐步达到所需的曲面.切勿一次弯曲成型。
5, arc processing: processing arc should be processed with special bending equipment, so that the plank will gradually reach the required surface.
6、批次:同一型号而不同批次的板材可能存在色差,不同色差的防锈铝板价格可能不同,出售和使用不同批次板材时应增加比对色差之程序,无视觉色差时方可在同一平面使用。
6, batch: the same type and different batches of plates may have chromatic aberration. The price of rust proof aluminum plates with different chromatic aberrations may be different. When selling and using different batches of plates, we should increase the procedure of comparing chromatic aberration. When no color difference is observed, they can be used in the same plane.
7、安装方向:将同色铝板安装在同一平面时,流程方向应一致,否则可能造视觉色差。
7, installation direction: when the same color aluminum plate is installed on the same plane, the direction of the process should be consistent, otherwise the visual color difference may be made.
8、撕膜:应在防锈铝板安装后的45天内撕去保护膜,否则可能发生撕膜困难或移胶现象。
8, tear film: the protective film should be tore out within 45 days after the installation of antirust aluminum plate, otherwise it may be difficult to tear film or remove glue.
9、使用条件:内墙板应在室内使用,不宜安装在室外,以保证使用效果和使用年限。
9, use conditions: the inner wall board should be used indoors, not in the outdoor, so as to ensure the use effect and the service life.

辽宁快乐12 四川11选5走势图 四川11选5走势图 四川11选5 四川11选5 吉林11选5 四川11选5开奖结果 吉林11选5 四川11选5 四川11选5官方网站